Inventor Add-insby Shaw Development

Add-on for Millworker · Inventor 2026 and 2027

NestCAM

Nest a whole job on your sheet stock from inside Inventor, then print the nest pages and labels and write the program for your CNC router. NestCAM reads Millworker's banding, grain and miter marks, so parts land the right way round.

Runs on top of Millworker in Autodesk Inventor 2026 and 2027.

A kitchen job nested by material.
Screenshotimg/shots/nestcam-sheet.png1600 × 900 pxNestCAM window open on a kitchen assembly: part list grouped by material on the left, sheet stock below it, the nest preview on the right showing nested sheets with grain lines and the cut route (blue cuts, cyan tabs, yellow dashed travel).
A kitchen job nested by material.

Nests by material

Every panel in the assembly, grouped by material with its quantity, size, grain and banding. Cut the job several times over with Sets. Tick or untick parts and sheets and the preview follows.

Knows your marks

Reads the banding, grain, miters, veneers and waste envelopes Millworker writes in the part files. Grain parts stay on the grain, Face 1 veneers lie up, miter allowance is added.

Lay it out by hand

Click a sheet to move, turn and nudge parts with snapping to the spacing and edge inset. Draw drops to keep offcuts. Anything that overlaps turns red. Your changes are kept when the job is nested again.

Nest pages and labels

One PDF page per sheet and one label per piece (4×2 roll or Avery 5163), with job, sheet and part IDs, banding and veneers. Report designs are your own.

CNC programs

Post processors for ShopBot, Weeke woodWOP (.mpr) and Anderson (.anc), plus a DXF per sheet with layer mapping and a 3D sheet assembly in Inventor for Inventor CAM.

Machine time

CNC info shows totals, sheets and tools: how long each sheet will run and which tools it uses, also in the tool report.

The sheet editor, with a drop drawn in.
Screenshotimg/shots/nestcam-editor.png1200 × 800 pxNestCAM sheet editor: one sheet large, a part being dragged with snapping, one drop drawn in blue-green with its size and ID.
The sheet editor, with a drop drawn in.
Nest pages.
Screenshotimg/shots/nestcam-pages.png1200 × 800 pxA NestCAM PDF nest page: sheet layout with part numbers and materials.
Nest pages.
Part labels.
Screenshotimg/shots/nestcam-labels.png1200 × 800 pxA page of NestCAM 4 x 2 part labels for the same sheet.
Part labels.

From model to machine

  1. Mark

    Mark banding, grain and miters with Millworker.

  2. Open

    Open NestCAM on the assembly and check the sheet stock.

  3. Nest

    Nest, tidy any sheet by hand, and untick sheets you are not cutting yet.

  4. Cut

    Click Nest and create PDFs: nest pages, labels, DXFs and CNC files go into the job's folder.

Details

Sheet stockSize, grain along, across or none, panel ID, Face 1 and Face 2, good side up or down per sheet.
Nest settingsOrigin corner, part spacing (3/8″ by default), edge inset (1/4″), banding deduction, label layout.
NumberingSheets numbered NEST{n}-SHEET{m} straight through every material; each job carries on its nest numbers.
Job infoJob, client, work order and due date from the assembly's iProperties.
MachinesImport your machine and tool library. More post processors on request.
Nest settings.
Screenshotimg/shots/nestcam-settings.png1200 × 800 pxThe NestCAM panel on the Millworker tab and its nest settings window.
Nest settings.
M

NestCAM needs Millworker

It nests the panels Millworker makes and marks, and puts its NestCAM panel on the Millworker ribbon tab. Each NestCAM seat needs a Millworker licence on the same seat. About Millworker · Pricing